Message
 Conatact Us
TEL:+086-0769-8201-7148
FAX:+086-0769-8201-7780
E-mail:ken13608@gmail.com

MSN:ken52103@hotmail.com
















Home >> Message
    These are very small cars (about 5 cm long), up to 25 km / h, which can be run virtually on the table. In the transmitter, there are batteries that can charge a small capacitor in the vehicle. The pos
12-7-30  Truggys
    RC Truggies are a hybrid form of buggy and monster truck dar. are currently relatively few events with racing truggy. The actual name is called stadium truck, but the name truggy originated from buggy
12-7-30  Monster Trucks
    Monster Truck RC monster trucks are usually not true to scale replica of a real monster trucks, but rather an independent vehicle models with overly large tires, suspension systems and good elaborate
12-7-30  Buggies
    RC Buggy Under buggies means remote controlled cars that are designed primarily for use off-road or off paved roads. They are equipped in contrast to the flat web models with strongly profiled tires
    The truck trial is all about, as precisely as possible to drive through rough terrain. The trial vehicles are often built and usually have to have as much power available, a very slow gear ratio. They
12-7-30  Trucks
    Remote-controlled truck (also called "truck model") are most often built in scales 1:16 (Wedico) and 1:14 (Tamiya). The larger scales 1:10, 1:12 and 1:8 are rarely represented. These models are usuall
12-7-30  Kit
    A kit is not assembled model. The components are contained in separate bags. A construction manual explaining the assembling step by step. It takes on the contrary to the RTR or separately purchased e
    An ARR-model is a fully pre-assembled model, where no remote control, a receiver and usually no battery is included.
    Under Ready to Run means a ready assembled model including the complete remote control. For remote control includes power, receiver and transmitter. This form of remote controlled cars, however, has t
    
    There are direct and indirect testing methods to assess the stamping property of the sheet metal. Practicality stamping test the most direct method to assess stamping forming property of the sheet me
    There are a lot of raw materials used in stamping forming and the properties of these materials may have large difference. The stamping forming can be succeeded only by determining the stamping method
    Many deformation processes can be done by stamping, the basic processes can be divided into two kinds, cutting and forming. Cutting is a shearing process that one part of the blank is cut form the ot
    Three are various processes of stamping forming with different working patterns and names. But these processes are similar to each other in plastic deformation. These are following conspicuous charact
    The characteristics of the sheet metal forming are as follows; high material utilization capacity to produce thin-walled parts of complex shape Good interchangeability stamping pares due to precisi
    Stamping is a kind of plastic forming process in which a part is produced by means of the plastic forming the material under the action of a diestamping is usually carried out under cold state, so it
12-6-8  Squeeze casting
    Squeeze casting, also known as liquid metal forging, is a combination of casting and forging process. The molten metal is poured into the bottom half of the pre-heated die. As the metal starts solid
12-6-8  Sand casting
    Sand casting is used to make large parts (typically Iron, but also Bronze, Brass, Aluminum). Molten metal is poured into a mold cavity formed out of sand (natural or synthetic). The processes of sand
    Powder metallurgy uses sintering process for making various parts out of metal powder. The metal powder is compacted by placing in a closed metal cavity (the die) under pressure. This compacted materi
    In plaster mold casting, a plaster, usually gypsum or calcium sulfate, is mixed with talc, sand, asbestos, and sodium silicate and water to form a slurry. This slurry is sprayed on the polished surfac
Total13Page Time:4/13Page Home pagePage up1 2 3  4 5 6 7 8 9 10 Next pageLast page
?style type="text/css">
line: CNC Machining | diamond saw blades | agie charmilles edm | meter seal | plastic seal | vibrating screen | Refractory Bricks | china wire mesh | wire mesh type | EDA bearings | china mechanical seals | slip ring | 6061 aluminum plate | concrete machinery manufacturer | concretemachinerypro.com | www.bst-pyrolysis.com | meltpump.net | Global Trade Info |
百度友情链接? 新濠天地(www.dzxm.net/xintiandi/) 时时彩开?/a>(www.eastpearl.net/shishicaikaihu/) 贝博娱乐?/a>(www.eqtdcbzx.com/beiboyulecheng/) 网上娱乐?/a>(www.e-topbi.com/wangshangyulecheng/) 博狗扑克(www.fjsei.com/bogoupuke/) 博狗(www.flywxt.com.cn/bogou/) 澳门娱乐?/a>(www.gdbzh.com/aomenyulecheng/) 赔率(www.glzysc.com/peilv/) 吉祥?/a>(www.gmdmw.com/jixiangfang/) 皇冠赌场(www.gmsgfwz.com/huangguanduchang/) 赌博技?/a>(www.zrgjok2008.com/dubojiqiao/)